; Default configuration file ; You can define your own receiver and invoke it by doing ; gnss-sdr --config_file=my_GNSS_SDR_configuration.conf ; [GNSS-SDR] ;######### GLOBAL OPTIONS ################## ;internal_fs_hz: Internal signal sampling frequency after the signal conditioning stage [Hz]. ;FOR USE GNSS-SDR WITH RTLSDR DONGLES USER MUST SET THE CALIBRATED SAMPLE RATE HERE ; i.e. using front-end-cal as reported here:http://www.cttc.es/publication/turning-a-television-into-a-gnss-receiver/ GNSS-SDR.internal_fs_hz=1200000 ;######### CONTROL_THREAD CONFIG ############ ControlThread.wait_for_flowgraph=false ;######### SUPL RRLP GPS assistance configuration ##### GNSS-SDR.SUPL_gps_enabled=false GNSS-SDR.SUPL_read_gps_assistance_xml=false GNSS-SDR.SUPL_gps_ephemeris_server=supl.google.com GNSS-SDR.SUPL_gps_ephemeris_port=7275 GNSS-SDR.SUPL_gps_acquisition_server=supl.google.com GNSS-SDR.SUPL_gps_acquisition_port=7275 GNSS-SDR.SUPL_MCC=244 GNSS-SDR.SUPL_MNS=5_1C GNSS-SDR.SUPL_LAC=0x59e2 GNSS-SDR.SUPL_CI=0x31b0 ;######### SIGNAL_SOURCE CONFIG ############ ;#implementation: Use [File_Signal_Source] or [UHD_Signal_Source] or [GN3S_Signal_Source] [Osmosdr_Signal_Source] SignalSource.implementation=RtlTcp_Signal_Source ;#item_type: Type and resolution for each of the signal samples. Use only gr_complex in this version. SignalSource.item_type=gr_complex ;#sampling_frequency: Original Signal sampling frequency in [Hz] ;FOR USE GNSS-SDR WITH RTLSDR DONGLES USER MUST SET THE CALIBRATED SAMPLE RATE HERE ; i.e. using front-end-cal as reported here:http://www.cttc.es/publication/turning-a-television-into-a-gnss-receiver/ SignalSource.sampling_frequency=1200000 ;#freq: RF front-end center frequency in [Hz] SignalSource.freq=1575420000 ;#gain: Front-end overall gain Gain in [dB] SignalSource.gain=40 ;#rf_gain: Front-end RF stage gain in [dB] SignalSource.rf_gain=40 ;#rf_gain: Front-end IF stage gain in [dB] SignalSource.if_gain=30 ;#AGC_enabled: Front-end AGC enabled or disabled SignalSource.AGC_enabled = false ;#samples: Number of samples to be processed. Notice that 0 indicates the entire file. SignalSource.samples=0 ;#repeat: Repeat the processing file. Disable this option in this version SignalSource.repeat=false ;#dump: Dump the Signal source data to a file. Disable this option in this version SignalSource.dump=false SignalSource.dump_filename=../data/signal_source.dat ;#enable_throttle_control: Enabling this option tells the signal source to keep the delay between samples in post processing. ; it helps to not overload the CPU, but the processing time will be longer. SignalSource.enable_throttle_control=false ;#Address of the rtl_tcp server (IPv6 allowed) SignalSource.address=127.0.0.1 ;#Port of the rtl_tcp server SignalSource.port=1234 ;# Set to true if I/Q samples come swapped SignalSource.swap_iq=false ;######### SIGNAL_CONDITIONER CONFIG ############ ;## It holds blocks to change data type, filter and resample input data. ;#implementation: Use [Pass_Through] or [Signal_Conditioner] ;#[Pass_Through] disables this block and the [DataTypeAdapter], [InputFilter] and [Resampler] blocks ;#[Signal_Conditioner] enables this block. Then you have to configure [DataTypeAdapter], [InputFilter] and [Resampler] blocks SignalConditioner.implementation=Signal_Conditioner ;######### DATA_TYPE_ADAPTER CONFIG ############ ;## Changes the type of input data. Please disable it in this version. ;#implementation: [Pass_Through] disables this block DataTypeAdapter.implementation=Pass_Through ;######### INPUT_FILTER CONFIG ############ ;## Filter the input data. Can be combined with frequency translation for IF signals ;#implementation: Use [Pass_Through] or [Fir_Filter] or [Freq_Xlating_Fir_Filter] ;#[Pass_Through] disables this block ;#[Fir_Filter] enables a FIR Filter ;#[Freq_Xlating_Fir_Filter] enables FIR filter and a composite frequency translation that shifts IF down to zero Hz. InputFilter.implementation=Freq_Xlating_Fir_Filter ;#dump: Dump the filtered data to a file. InputFilter.dump=false ;#dump_filename: Log path and filename. InputFilter.dump_filename=../data/input_filter.dat ;#The following options are used in the filter design of Fir_Filter and Freq_Xlating_Fir_Filter implementation. ;#These options are based on parameters of gnuradio's function: gr_remez. ;#These function calculates the optimal (in the Chebyshev/minimax sense) FIR filter inpulse reponse given a set of band edges, the desired reponse on those bands, and the weight given to the error in those bands. ;#input_item_type: Type and resolution for input signal samples. Use only gr_complex in this version. InputFilter.input_item_type=gr_complex ;#outut_item_type: Type and resolution for output filtered signal samples. Use only gr_complex in this version. InputFilter.output_item_type=gr_complex ;#taps_item_type: Type and resolution for the taps of the filter. Use only float in this version. InputFilter.taps_item_type=float ;#number_of_taps: Number of taps in the filter. Increasing this parameter increases the processing time InputFilter.number_of_taps=5 ;#number_of _bands: Number of frequency bands in the filter. InputFilter.number_of_bands=2 ;#bands: frequency at the band edges [ b1 e1 b2 e2 b3 e3 ...]. ;#Frequency is in the range [0, 1], with 1 being the Nyquist frequency (Fs/2) ;#The number of band_begin and band_end elements must match the number of bands InputFilter.band1_begin=0.0 InputFilter.band1_end=0.45 InputFilter.band2_begin=0.55 InputFilter.band2_end=1.0 ;#ampl: desired amplitude at the band edges [ a(b1) a(e1) a(b2) a(e2) ...]. ;#The number of ampl_begin and ampl_end elements must match the number of bands InputFilter.ampl1_begin=1.0 InputFilter.ampl1_end=1.0 InputFilter.ampl2_begin=0.0 InputFilter.ampl2_end=0.0 ;#band_error: weighting applied to each band (usually 1). ;#The number of band_error elements must match the number of bands InputFilter.band1_error=1.0 InputFilter.band2_error=1.0 ;#filter_type: one of "bandpass", "hilbert" or "differentiator" InputFilter.filter_type=bandpass ;#grid_density: determines how accurately the filter will be constructed. ;The minimum value is 16; higher values are slower to compute the filter. InputFilter.grid_density=16 ;#The following options are used only in Freq_Xlating_Fir_Filter implementation. ;#InputFilter.IF is the intermediate frequency (in Hz) shifted down to zero Hz ;FOR USE GNSS-SDR WITH RTLSDR DONGLES USER MUST SET THE CALIBRATED SAMPLE RATE HERE ; i.e. using front-end-cal as reported here:http://www.cttc.es/publication/turning-a-television-into-a-gnss-receiver/ InputFilter.sampling_frequency=1200000 ;# IF deviation due to front-end LO inaccuracies [HZ] InputFilter.IF=80558 ;######### RESAMPLER CONFIG ############ ;## Resamples the input data. ;# DISABLED IN THE RTL-SDR REALTIME ;#implementation: Use [Pass_Through] or [Direct_Resampler] ;#[Pass_Through] disables this block Resampler.implementation=Pass_Through ;######### CHANNELS GLOBAL CONFIG ############ ;#count: Number of available GPS satellite channels. Channels_1C.count=4 ;#in_acquisition: Number of channels simultaneously acquiring for the whole receiver Channels.in_acquisition=1 Channel.signal=1C ;######### ACQUISITION GLOBAL CONFIG ############ ;#dump: Enable or disable the acquisition internal data file logging [true] or [false] Acquisition_1C.dump=false ;#filename: Log path and filename Acquisition_1C.dump_filename=./acq_dump.dat ;#item_type: Type and resolution for each of the signal samples. Use only gr_complex in this version. Acquisition_1C.item_type=gr_complex ;#if: Signal intermediate frequency in [Hz] Acquisition_1C.if=0 ;#sampled_ms: Signal block duration for the acquisition signal detection [ms] Acquisition_1C.sampled_ms=1 ;#implementation: Acquisition algorithm selection for this channel: [GPS_L1_CA_PCPS_Acquisition] or [Galileo_E1_PCPS_Ambiguous_Acquisition] Acquisition_1C.implementation=GPS_L1_CA_PCPS_Acquisition_Fine_Doppler ;#threshold: Acquisition threshold Acquisition_1C.threshold=0.015 ;#pfa: Acquisition false alarm probability. This option overrides the threshold option. Only use with implementations: [GPS_L1_CA_PCPS_Acquisition] or [Galileo_E1_PCPS_Ambiguous_Acquisition] ;Acquisition_1C.pfa=0.0001 ;#doppler_max: Maximum expected Doppler shift [Hz] Acquisition_1C.doppler_max=10000 ;#doppler_max: Maximum expected Doppler shift [Hz] Acquisition_1C.doppler_min=-10000 ;#doppler_step Doppler step in the grid search [Hz] Acquisition_1C.doppler_step=500 ;#maximum dwells Acquisition_1C.max_dwells=15 ;######### TRACKING GLOBAL CONFIG ############ ;#implementation: Selected tracking algorithm: [GPS_L1_CA_DLL_PLL_Tracking] or [GPS_L1_CA_DLL_PLL_C_Aid_Tracking] [GPS_L1_CA_DLL_PLL_Optim_Tracking] Tracking_1C.implementation=GPS_L1_CA_DLL_PLL_Tracking ;#item_type: Type and resolution for each of the signal samples. Tracking_1C.item_type=gr_complex ;#sampling_frequency: Signal Intermediate Frequency in [Hz] Tracking_1C.if=0 ;#dump: Enable or disable the Tracking internal binary data file logging [true] or [false] Tracking_1C.dump=false ;#dump_filename: Log path and filename. Notice that the tracking channel will add "x.dat" where x is the channel number. Tracking_1C.dump_filename=./tracking_ch_ ;#pll_bw_hz: PLL loop filter bandwidth [Hz] Tracking_1C.pll_bw_hz=40.0; ;#dll_bw_hz: DLL loop filter bandwidth [Hz] Tracking_1C.dll_bw_hz=2.0; ;#order: PLL/DLL loop filter order [2] or [3] Tracking_1C.order=3; ;#early_late_space_chips: correlator early-late space [chips]. Use [0.5] Tracking_1C.early_late_space_chips=0.5; ;######### TELEMETRY DECODER GPS CONFIG ############ ;#implementation: Use [GPS_L1_CA_Telemetry_Decoder] for GPS L1 C/A TelemetryDecoder_1C.implementation=GPS_L1_CA_Telemetry_Decoder TelemetryDecoder_1C.dump=false ;#decimation factor TelemetryDecoder_1C.decimation_factor=1; ;######### OBSERVABLES CONFIG ############ ;#implementation: Use [GPS_L1_CA_Observables] for GPS L1 C/A. Observables.implementation=GPS_L1_CA_Observables ;#dump: Enable or disable the Observables internal binary data file logging [true] or [false] Observables.dump=false ;#dump_filename: Log path and filename. Observables.dump_filename=./observables.dat ;######### PVT CONFIG ############ ;#implementation: Position Velocity and Time (PVT) implementation algorithm: Use [GPS_L1_CA_PVT] in this version. PVT.implementation=GPS_L1_CA_PVT ;#averaging_depth: Number of PVT observations in the moving average algorithm PVT.averaging_depth=10 ;#flag_average: Enables the PVT averaging between output intervals (arithmetic mean) [true] or [false] PVT.flag_averaging=true ;#output_rate_ms: Period between two PVT outputs. Notice that the minimum period is equal to the tracking integration time (for GPS CA L1 is 1ms) [ms] PVT.output_rate_ms=100 ;#display_rate_ms: Position console print (std::out) interval [ms]. Notice that output_rate_ms<=display_rate_ms. PVT.display_rate_ms=500 ;# KML, GeoJSON, NMEA and RTCM output configuration ;#dump_filename: Log path and filename without extension. Notice that PVT will add ".dat" to the binary dump and ".kml" to GoogleEarth dump. PVT.dump_filename=./PVT ;#nmea_dump_filename: NMEA log path and filename PVT.nmea_dump_filename=./gnss_sdr_pvt.nmea; ;#flag_nmea_tty_port: Enable or disable the NMEA log to a serial TTY port (Can be used with real hardware or virtual one) PVT.flag_nmea_tty_port=false; ;#nmea_dump_devname: serial device descriptor for NMEA logging PVT.nmea_dump_devname=/dev/pts/4 PVT.flag_rtcm_server=false PVT.flag_rtcm_tty_port=false PVT.rtcm_dump_devname=/dev/pts/1 ;#dump: Enable or disable the PVT internal binary data file logging [true] or [false] PVT.dump=true